BWBV0003251
Artikel 49
Internationaal Verdrag van Torremolinos voor de beveiliging van vissersvaartuigen, 1977
(1) An efficient bilge pumping plant shall be provided which under all practical conditions shall be capable of pumping from and draining any watertight compartment which is neither a permanent oil tank nor a permanent water tank whether the vessel is upright or listed. Wing suctions shall be provided if necessary for that purpose. Arrangements shall be provided for easy flow of water to the suction pipes. Provided the Administration is satisfied that the safety of the vessel is not impaired the bilge pumping arrangements may be dispensed with in particular compartments.
(2) (a) At least two independently driven power bilge pumps shall be provided, one of which may be driven by the main engine. A ballast pump or other general service pump of sufficient capacity may be used as a power driven bilge pump.
(b) Power bilge pumps shall be capable of giving a speed of water of at least 2 metres per second through the main bilge pipe which shall have an internal diameter of at least: where: d is the internal diameter in millimetres, and L, B and D are in metres.
(c) Each of the bilge pumps provided in accordance with this Regulation shall be provided with a direct bilge suction, one of these suctions drawing from the port side of the machinery space and the other from the starboard side, except that in the case of a vessel of less than 75 metres in length only one bilge pump need be provided with a direct bilge suction.
(d) No bilge suction shall have an inside diameter of less than 50 millimetres. The arrangement and sizing of the bilge system shall be such that the full rated capacity of the pump specified above can be applied to each of the watertight compartments located between the collision and afterpeak bulkheads.
(a) At least two independently driven power bilge pumps shall be provided, one of which may be driven by the main engine. A ballast pump or other general service pump of sufficient capacity may be used as a power driven bilge pump.
(b) Power bilge pumps shall be capable of giving a speed of water of at least 2 metres per second through the main bilge pipe which shall have an internal diameter of at least: where: d is the internal diameter in millimetres, and L, B and D are in metres.
(c) Each of the bilge pumps provided in accordance with this Regulation shall be provided with a direct bilge suction, one of these suctions drawing from the port side of the machinery space and the other from the starboard side, except that in the case of a vessel of less than 75 metres in length only one bilge pump need be provided with a direct bilge suction.
(d) No bilge suction shall have an inside diameter of less than 50 millimetres. The arrangement and sizing of the bilge system shall be such that the full rated capacity of the pump specified above can be applied to each of the watertight compartments located between the collision and afterpeak bulkheads.
(3) A bilge ejector in combination with an independently driven high pressure sea-water pump may be installed as a substitute for one independently driven bilge pump required by paragraph (2)(a), provided this arrangement is to the satisfaction of the Administration.
(4) In vessels where fish handling or processing may cause quantities of water to accumulate in enclosed spaces, adequate drainage shall be provided.
(5) Bilge pipes shall not be led through fuel oil, ballast or double bottom tanks, unless these pipes are of heavy gauge steel construction.
(6) Bilge and ballast pumping systems shall be arranged so as to prevent water passing from the sea or from water ballast spaces into holds or into machinery spaces or from one watertight compartment to another. The bilge connexion to any pump which draws from the sea or from water ballast spaces shall be fitted with either a non-return valve or a cock which cannot be opened simultaneously either to the bilges and to the sea or to the bilges and water ballast spaces. Valves in bilge distribution boxes shall be of a non-return type.
(7) Any bilge pipe piercing a collision bulkhead shall be fitted with a positive means of closing at the bulkhead with remote control from the working deck with an indicator showing the position of the valve provided that, if the valve is fitted on the after side of the bulkhead and is readily accessible under all service conditions, the remote control may be dispensed with.
(2) (a) At least two independently driven power bilge pumps shall be provided, one of which may be driven by the main engine. A ballast pump or other general service pump of sufficient capacity may be used as a power driven bilge pump.
(b) Power bilge pumps shall be capable of giving a speed of water of at least 2 metres per second through the main bilge pipe which shall have an internal diameter of at least: where: d is the internal diameter in millimetres, and L, B and D are in metres.
(c) Each of the bilge pumps provided in accordance with this Regulation shall be provided with a direct bilge suction, one of these suctions drawing from the port side of the machinery space and the other from the starboard side, except that in the case of a vessel of less than 75 metres in length only one bilge pump need be provided with a direct bilge suction.
(d) No bilge suction shall have an inside diameter of less than 50 millimetres. The arrangement and sizing of the bilge system shall be such that the full rated capacity of the pump specified above can be applied to each of the watertight compartments located between the collision and afterpeak bulkheads.
(a) At least two independently driven power bilge pumps shall be provided, one of which may be driven by the main engine. A ballast pump or other general service pump of sufficient capacity may be used as a power driven bilge pump.
(b) Power bilge pumps shall be capable of giving a speed of water of at least 2 metres per second through the main bilge pipe which shall have an internal diameter of at least: where: d is the internal diameter in millimetres, and L, B and D are in metres.
(c) Each of the bilge pumps provided in accordance with this Regulation shall be provided with a direct bilge suction, one of these suctions drawing from the port side of the machinery space and the other from the starboard side, except that in the case of a vessel of less than 75 metres in length only one bilge pump need be provided with a direct bilge suction.
(d) No bilge suction shall have an inside diameter of less than 50 millimetres. The arrangement and sizing of the bilge system shall be such that the full rated capacity of the pump specified above can be applied to each of the watertight compartments located between the collision and afterpeak bulkheads.
(3) A bilge ejector in combination with an independently driven high pressure sea-water pump may be installed as a substitute for one independently driven bilge pump required by paragraph (2)(a), provided this arrangement is to the satisfaction of the Administration.
(4) In vessels where fish handling or processing may cause quantities of water to accumulate in enclosed spaces, adequate drainage shall be provided.
(5) Bilge pipes shall not be led through fuel oil, ballast or double bottom tanks, unless these pipes are of heavy gauge steel construction.
(6) Bilge and ballast pumping systems shall be arranged so as to prevent water passing from the sea or from water ballast spaces into holds or into machinery spaces or from one watertight compartment to another. The bilge connexion to any pump which draws from the sea or from water ballast spaces shall be fitted with either a non-return valve or a cock which cannot be opened simultaneously either to the bilges and to the sea or to the bilges and water ballast spaces. Valves in bilge distribution boxes shall be of a non-return type.
(7) Any bilge pipe piercing a collision bulkhead shall be fitted with a positive means of closing at the bulkhead with remote control from the working deck with an indicator showing the position of the valve provided that, if the valve is fitted on the after side of the bulkhead and is readily accessible under all service conditions, the remote control may be dispensed with.
- Citeren als
- Art. 49
- Status
- Geldend recht
- Identificatie
- BWBV0003251
- Officiële bron
- wetten.overheid.nl